Replacement IR lamp for Sidel SBO 4/6

Thu, 30 Jul 2026 10:10:58 +0800

Getting Your Sidel SBO 4/6 Back Up to Speed

If you’re running a Sidel SBO 4/6, you know the drill. Your lamps are the heart of the operation. If they’re off, your bottles are off. That’s why we built our short-wave IR lamps to be a simple, “plug-and-play” swap. The goal here is simple: get the heat deep into the PET preform without scorching the outside. No burnt plastic, no thin spots. Just a perfect blow every time. The Nitty-Gritty on Power Wall thickness is everything. To get it right, you need a very specific balance of wattage and voltage. We use high-voltage quartz glass because these lamps take a beating with constant heating and cooling. Plus, we matched the electrical resistance of the original Sidel elements. Why? Because nobody wants to deal with a tripped circuit breaker or voltage drops in the middle of a shift. It just works. No More Fighting with Sockets We’ve all been there—it’s midnight, the machine is down, and you’re fighting a connector that won’t seat. We hate that. That’s why we build our R7s and Sk15 connectors to tight tolerances. They slide right in. We also use heavy-wall quartz tubing so the filament doesn’t sag when things get hot, and a halogen gas fill to keep the tungsten from evaporating. It basically means your lamps last longer, even when you’re pushing them to the limit. Making it Fit You shouldn’t have to mess with your reflectors or modify your oven. We standardized the length and pin spacing to fit about 95% of the blow molding setups out there. You just swap them in and get back to work. One quick tip, though: high-density lamps put a lot of stress on your ventilation. If you crank up the wattage to speed up your cycles, make sure your cooling blowers are actually clean. If the air is choked, the quartz gets too hot and the lamp dies early. We keep these in stock, too. No more waiting weeks for OEM parts while your production line sits idle.

Replacement lamp for SIG Blomax 4/6/8/10

Fri, 17 Jul 2026 09:29:18 +0800

Getting Your Heat Right on the SIPA Blomax 4/6/8/10

If you’ve spent any time on a PET blow molding floor, you know the nightmare of uneven heating. One minute everything is fine, and the next, you’re staring at bottles with wonky wall thickness or, worse, a pile of failures. A lot of the time, this happens because of a “quick fix.” You swap out a worn-out lamp for a generic one that looks right, but the wattage is slightly off. Suddenly, you’ve got cold spots in your oven. It’s frustrating. That’s why we build our lamps to be exact clones of the originals. No guessing. No “close enough.” Just a drop-in replacement that hits the same power density as the OEM gear. The math behind the heat Here’s the thing: mixing lamps with different resistance values is a recipe for disaster. Even a tiny 5% difference in voltage or wattage shifts how the infrared heat hits the preform. When that happens, your PID controllers start working overtime. They “hunt” for the right temperature, swinging back and forth, which just makes your preform temps unstable. We match the specs exactly so your controllers can just… relax. Everything stays steady. It’s all in the fit We use high-purity quartz because it can take the punch of rapid heating and cooling without cracking. But the glass is only half the story. The connectors (R7s or Sk15) have to be tight. If there’s a loose fit at the terminal, you get arcing. That’s how you burn out the ends of a lamp way before its time. Plus, the lamp has to sit perfectly centered in the reflector. If it sags or sits crooked, you’re wasting energy and losing that precious reflection. It’s a small detail, but it’s the difference between a smooth run and a headache. A quick reality check for the shop floor High-density infrared lamps put out a massive amount of heat. That’s great for your cycle times, but it puts a lot of pressure on your cooling fans. Keep an eye on your ventilation. If dust builds up and blocks the airflow, your lamp housing is going to overheat. And once that happens, it doesn’t matter how high the quality of the quartz is—the lamp is going to die early. Keep it clean, keep the power matched, and your Blomax will behave exactly the way it should.

4/6 on IR Element Supply Co.

Replacement IR lamp for Sidel SBO 4/6

Getting Your Sidel SBO 4/6 Back Up to Speed

Replacement lamp for SIG Blomax 4/6/8/10

Getting Your Heat Right on the SIPA Blomax 4/6/8/10